Hi Steve, Just tried as you suggested, notta. Regards, Barry. -----Original Message----- From: blind-sysadmins-bounces@lists.hodgsonfamily.org [mailto:blind-sysadmins-bounces@lists.hodgsonfamily.org] On Behalf Of Steve Nutt Sent: Friday, August 26, 2011 12:01 AM To: 'Blind sysadmins list' Subject: Re: [Blind-sysadmins] Configuring an FTP Server Hi Barry, Set the starting port to 20 and the end to 21, and see what happens. All the best Steve -- Computer Room Services 77 Exeter Close Stevenage Hertfordshire SG1 4PW Tel: 01438-742286 Mob: 07956334938 Fax: 01438-759589 Email: steve@comproom.co.uk Web: http://www.comproom.co.uk -----Original Message----- From: blind-sysadmins-bounces@lists.hodgsonfamily.org [mailto:blind-sysadmins-bounces@lists.hodgsonfamily.org] On Behalf Of Barry Toner Sent: Thursday 25 August 2011 23:56 To: Blind sysadmins list Subject: [Blind-sysadmins] Configuring an FTP Server Hi Folks, I haven't done this in about 4 years, and am coming a bit unstuck. I could really do with some thoughts on the below. Where I'm coming from... When i ran an FTP server back in the day, I was using XP with it's, (cauf, cauf), Firewall, Eset NOD32 AV, ServU FTP Server and a Linksys WRT 54G. How life seemed much more simple... Now, the box I'm going to use for the Server has Windows 7, a Draytek Router and File Zilla Server. It also has Windows Firewall & Eset Smart Security. I've installed FS Server and created a test account. I've set my Desktop up with a Static IP on the LAN. Giving the Drayteks IP as the Gateway, and the DNS Server it specified. Connection to other machines on the LAN and out to the Internet is fine. I cant' get a connection into my FTP Server. I've read here, http://www.draytek.co.uk/support/kb_vigor_portforwarding.html how to "Open a port" on the Draytek. I specified the IP for the box the Servers running on. Applied the setting,and confirmed it was in the Port Forwarding table, with start and end ports of 21. I temporarily turned off both Windows Firewall & esets Firewall, then went to, http://ftptest.net/ To test the connection from outside the LAN. It's still timing out, and the Servers showing no attempts in the log. It's not getting through somewhere... I did spy something in FZs' FAQ here http://goo.gl/mlydm regarding Passive Mode. I didnt' understand if this was absolutely necessary. It's been a long time and I remember people could connect using (Active, used to be the default mode), or Passive in their client. The above article, talks about settings in FZ, sticking it to an IP and custum port between 5000 and 5100. It doesn't mention if I did this if I'd then also need to open these ports on my router. FYI, File Zilla reports that it is Online and not Locked. NB. I will more than likely leave Windows Firewall disabled and figure out how to create a rule in Esets Firewall for the server once I confirm it's coming through the draytek, i'll worry about the software stuff. Also, I'm going to use something like a Dynamic DNS client once I've got the connection working. The ISP, I seriously doubt would happily hand out a Static IPv4 address to me these days. Any thoughts of what to try next? Cheers, Barry. _______________________________________________ Blind-sysadmins mailing list Blind-sysadmins@lists.hodgsonfamily.org http://lists.hodgsonfamily.org/listinfo/blind-sysadmins _______________________________________________ Blind-sysadmins mailing list Blind-sysadmins@lists.hodgsonfamily.org http://lists.hodgsonfamily.org/listinfo/blind-sysadmins __________ Information from ESET Smart Security, version of virus signature database 6410 (20110825) __________ The message was checked by ESET Smart Security. http://www.eset.com